In recent weeks Thermaltake has been busy releasing a selection of ARGB based products with my most recent review being the Water 3.0 360 ARGB. For the most part, these new products are refreshed versions of existing models, and this is exactly the case with the new Thermaltake Level 20 GT ARGB.
I previously reviewed the Thermaltake Level 20 GT RGB back in August, and it has been one of my favourite cases to date. There are some caveats with it though, it is absolutely massive and at £250+ it is expensive, but if you are building a high-end rig with elaborate water cooling it is an excellent investment and the case I use personally.
The Level 20 GT Tempered Glass ARGB, from what I can tell, is an identical chassis but Thermaltake have swapped out the Ring Plus fans and fitted it with two 200mm 5V ARGB LED front fans and one 140mm rear fan. It is worth noting that the Level 20 GT RGB Plus had an RGB fan on its exhaust as well as the two front fans, while this one no
The change in fans has brought a lower price point of £220, so around a 12% saving which is not to be sniffed at. You can buy the chassis with no front fans for just £175, however, if you want RGB and went for two 200mm Thermaltake Pure 20 Fans this would set you back £74 so it is cheaper to go with this model.
Last updated on 12th March 2019 2:16 pm
Apart from the fans and fan hub, I am not aware of any difference between the Level 20 GT models.
This case is constructed
from steel and tempered glass so it is a hefty 20KG and equally massive dimensions
of 580 x 294 x 592 mm. Similar to many of the Thermaltake cases, this uses
their Dismantlable Modular Design, so you can strip the case down to the bare
bones if you are a keen modder, or take out all the unused features providing
increased airflow. This makes building
and maintanence easier too as gaining
access to the ceiling radiator mounts very easy as well as accessing the front
It features four tempered glass panels with locking hinged doors with each panel being 5mm thick. Airflow has been thought of, and both the top and front panel sit slightly raised from the mesh dust guard, with decent sized vent holes around the edges. On the case I reviewed back in August which I still use, I have cleaned the front filters twice, so it is clearly pulling in enough air to trap quite a bit of dust.
The two pre-installed 200mm 5V ARGB LED front fans featuring
hydraulic bearing, 9 addressable LEDs and
16.8 million-colour illumination to guarantee high airflow and custom system
designs to show off your PC design skills.
The 5V ARGB LED fans can be controlled using a simple interface
built into the I/O panel that cycles through 7 different lighting modes and a
range of different colour options. This is
something that is worth considering if you want to control the ARGB fans, your motherboard will need a 5v 3-pin
connector, mine only had a 12v four-pin
Assuming you can connect the RGB header you can sync the
fans with almost any motherboard software including SUS Aura Sync, GIGABYTE RGB
Fusion, MSI Mystic Light Sync and AsRock Polychrome.
The Level 20 GT ARGB supports up to E-ATX motherboards, CPU
coolers up to 200mm in height, VGA lengths up to 310mm and PSU sizes up to 220mm in length.
The case features a patented rotational PCI-E system allowing
you to stack multiple GPUs either vertically or horizontally, depending on how
you want to build your system. However,
just like the previous model, you will need to invest in a PCIe riser cable if you want to mount
your GPU vertically.
On the bottom of the case is a removable PSU shroud which is screwed into place. You also get a decent amount
of storage options with a rack in the front for four 3.5inch drives plus two
brackets for SSDs, one on the PSU shroud the other just next to it. Then on the
rear side of the case are three mount plates
which can accept either two 2.5-inch or one 3.5-inch drive. So in total, you could
have ten SSDs or seven 3.5-inch drives.
As you would hope for a case of this size, it is an absolute
beast for water cooling options. The Level 20 GT ARGB lets you mount your
radiator against the back panel to show off your RGB fans. The back panel provides adequate exhaust while
putting your fans on display, with support for up to a 420mm radiator.
The front of the case can accommodate up to 420mm radiators which
us 140mm fans, or 360mm radiators for 120mm fans, this also includes AIO coolers.
The top can accept everything up to 360mm
The rear of the case can accept fans and radiators up to 140mm, and you can even install
up to 240mm on the bottom.
You already have 200mm fans in the front of the case, but
the top also accepts up to two 200m fans
or alternative 3×120/140mm.
At the leading edge of the top panel are two USB 2.0 ports,
two USB 3.0 ports and a single USB 3.1 Gen 2 Type-C header on the right side.
Headphone and microphone jacks, power and reset buttons and a hard drive
activity light are on the left side.
Just like the last build, this case is a pleasure to work with, mainly because it is so large you are never too cramped when doing anything. The hinged doors feel super premium, and they are easy to slot off. The fact there are four tempered glass panels means your cable management skills need to be decent, I honestly don’t know how it is possible to have the under-side panel neat with all the fan cables and PSU cables. I did find the hinged door was quite forgiving when it came to closing it, unlike slide on panels which can be problematic when you have a lot of cables.
One of the particular highlights of this case is being able
to remove the plastic cover on the top of the case, and then remove the entire radiator
mounting section. This allows you to
mount a radiator outside of the case and install
it when done. With the roof mount out of
the way you also have easy access to all the fan ports and CPU power socket at
the top of the motherboard.
On the flip side, the most awkward part of the build is the
PSU shroud, you need to remove it to install the PSU and cables, and this then
requires you to unscrew it at various places. It is not a significant problem, and being able to remove
the cover is arguably better than having one fixed in place. You just need to remember where all the little
screw holes are when you are done.
With my build, I installed the 360mm Floe Riing RGB Premium Edition into the roof of the case. Unfortunately, this case arrives after I did the Water 3.0 ARGB review.
With the ARGB fans on this case, it is technically an easier build overall, as the fans are all
pre-wired into the controller, so you only have the SATA power cable and RGB
header to plug in.
Overall, I think this is one of the easiest cases I have worked with, and for the more adventurous it
has an exceptional level of modability.
I don’t have a dedicated test build or review enough cases to be able to objectively test a cases cooling ability against other cases. The fact that I am using a 360mm AIO radiator skews the cooling results somewhat. However, the case runs both cool and quiet, I have a moderate overclock on my Ryzen 2600, running at 4Ghz and this happily sits at around 34-degrees for general office use. Similarly, the motherboard temperatures all site at approximately 28-degrees and my GTX 1070 which I keep at stock speeds stays in passive mode at 50-degrees.
Subjectively I would say this runs fractionally louder than the RGB model, but I don’t have any
hardware accurate enough to test this. The specification of the front fans
states the same noise level of 29.2dBA. Even if it is louder, it is still very quiet, first thing in the morning when
there is no traffic noise, and I have no other background noise on, I can just
about hear the fans gently spinning, and it is likely that it is the 120mm fans
of the radiator that are the loudest component, not
the 200mm front fans.
I loved the Level 20 GT RGB Plus back in August, but at the
time it was priced at £300 making it only
suitable for extravagant high-end builds. Since then it has dropped in price by
about 20% down to £250 making it much more appealing. The Level 20 GT ARGB is
even cheaper at £220, and in some respects,
it is a slighter better case.
The ARGB fans have a nicer
lighting appearance with the colours seamlessly integrating into each other emanating
out from the centre of the fan. With the RGB fans,
the LEDs runs around the edge with each LED being clearly visible. It’s an aesthetic difference I didn’t realise I
cared about until running these cases side by side, but I can now see why ARGB
is a popular option.
The installation is arguably easier with this build, and I think many people will prefer the option
to control the ARGB with the motherboard software rather than the TT RGB Plus
The only downside will be if you don’t have the 5v 3-pin
header on your motherboard, this will mean you are forced to use the manual
controls. For me, that is not an issue,
but if you want everything to sync up
then the previous Level 20 GT RGB Plus case will probably be worth the extra
Overall then, assuming your motherboard is compatible, this will be a superior case primarily because it is about £30 cheaper which is a 12% saving.
Thermaltake Level 20 GT Tempered Glass ARGB Full Tower PC Case Review
Product Name: Thermaltake Level 20 GT Tempered Glass ARGB Full Tower PC Case